Ultrasonic Level Transmitter LIT25
- Simple Calibration with 2-button keypad
- Large 4-digit LCD display
- Non-Contacting, no maintenance sensor
- Isolated 4-20 mA output (1000 ohm)
- Relay for alarm or control
- Automatic temperature compensation
- Low Cost High accuracy (±0.25%)
- Watertight, dust tight enclosure
- Simple Calibration with 2-button keypad
- Large 4-digit LCD display
- Non-Contacting, no maintenance sensor
- Isolated 4-20 mA output (1000 ohm)
- Relay for alarm or control
- Automatic temperature compensation
- Low Cost High accuracy (±0.25%)
- Watertight, dust tight enclosure
Transmits : Ultrasonic Level Transmitter LIT25 features a 4-20 mA output rated up to 1000 ohms. This output is isolated and ready for direct connection to your PLC or Controller.
Displays : Mount the watertight display enclosure at a convenient location where the large, 4-digit LCD Display is visible to Operators. Use the built-in Keypad for calibration without climbing the Tank.
Controls : Use Ultrasonic Level Transmitter LIT25 signal Relay output to control pumps and alarms. Calibrate for level, echo loss or temperature alarm.
NON-CONTACTING SENSOR
Ultrasonic Level Transmitter LIT25, echo-ranging sensor mounts at the top of the tank to continuously monitor level. No maintenance is required.
A built-in temperature sensor is included to automatically compensate for changes in speed of sound due to temperature. Level and temperature signals share a single coaxial cable which can be run up to 500 ft (152 m) to the electronics enclosure. The standard Sensor is rated for tank sizes up to 32 ft. (10 m) high, and is made with PVC and Teflon (an optional all-Teflon model is also available). The sensor and cable is rated intrinsically safe (with optional intrinsic safety barrier) for installation in hazardous rated tanks.
EASY CALIBRATION WITHOUT CLIMBING TANKS
Use the 2-button keypad built into Ultrasonic Level Transmitter LIT25 display enclosure to directly enter the measurement span and relay set-points in inches or cm. No calibration targets or level simulations are required. Calibration values are stored through power interruptions and no battery is required.
DESIGNED FOR OPERATOR CONVENIENCE
Mount Ultrasonic Level Transmitter LIT25 Display enclosure at a convenient location for operators. The large LIT25 digital display indicates that it is calibrated in percent, inches or cm, and in RANGE or LEVEL mode. Relay status is also displayed and the ECHO symbol flashes to indicate that echos are being received normally.
Special LIT25 features like OUTPUT SIMULATION allow operators to test calibration, loop wiring, and relay set-points directly from the LIT25 keypad. Simplify calibration or tank measurement with the LIT25’s RANGE display – instantly display distance in inches or cm from the sensor to the target or liquid surface.
Use the LIT25 keypad to increase or decrease DAMPING and control the instrument’s response to turbulence, wave action or agitators. Increase damping to completely reject agitator blades or other moving obstructions even when they travel through the sensor sound path.
LEVEL or TEMPERATURE CONTROL
Calibrate the versatile Ultrasonic Level Transmitter LIT25 relay for your choice of level alarm, pump control, temperature alarm or echo loss alarm. Relay ON and OFF set-points are independently adjustable through the LIT25 calibration keypad. You can even control the LIT25’s response to an echo loss condition – Hold the last reading, output 20mA or output 4mA.
- Chemical Storage Tanks
- Sumps
- Reservoirs
- Lagoons.
General Specifications
- Electronics Enclosure: Watertight, dust tight NEMA4X (IP 66) poly-carbonate with clear, shatterproof cover
- Accuracy: ±0.25% of Range or 2 mm (0.08"), whichever is greater
- Display: Large (3/4 in, 19 mm high) 4 digit LCD
- Calibration: Selectable Level or Range mode. Enter min. and max. distance in inches or cm
- Programming: Built-in 2-button keypad with Menu selection. Calibration parameters are permanent when Stored (even through a power interruption)
- Power Input: 100-130VAC 50/60Hz, 5 watts maximum
- Output: Isolated 4-20mA, 1000 ohm load maximum
- Signal Relay: Qty 1, rated 120/240VAC or 24VDC, 1 ampere, programmable for level alarm, echo loss alarm, pump control or temperature alarm
- Temperature Compensation: Temperature probe inside level sensor for high accuracy in changing temperatures
- Electrical Surge Protection: Sensor, 4-20 mA and AC power input
- Operating Temperature (electronics): -13 to 140°F (-25 to 60°C)
- Approximate Shipping Weight: 6 lbs. (2.7 kg)
Sensor Specifications
- Maximum Range: 32 ft (10 m)
- Deadband (Blanking): Programmable, Minimum 12 in (305 mm)
- Beam Angle: 8° Locate 1 ft (300 mm) from tank sidewall for every 10 ft (3 m) depth
- Operating Frequency: 42 KHz
- Exposed Materials: PVC and Teflon
- Operating Temperature: -40 to 150°F (-40 to 65°C)
- Operating Pressure: 20 psi (1.35 bar) maximum
- Sensor Cable: RG62AU coaxial, 25 ft (7.6 m) standard length (See Options)
Options
- Sensors: All Teflon construction / flange mount / 50 ft (15.6 m) range
- Hazardous Locations: Intrinsically safe Sensors CSA rated Class I,II,III, Div. I,II, Groups C,D,E,F,G
- Sensor Cable: 50 ft (15 m) RG62AU coaxial continuous from Sensor, or splice up to 500 ft (150 m)
- Sensor Cable Junction Box: Watertight NEMA4 steel with connection terminal strip
- Power Input: 200-250VAC 50/60Hz, 12VDC or 24VDC
- Enclosure Panel Mount: Flange assembly mounts standard enclosure
Ultrasonic sensors are mounted at the top of a tank or in a position above the liquid being measured. The sensor continuously transmits pulses of high frequency sound (typically 42 kHz) which travel away from the sensor, hit the surface of the liquid and return to the sensor.
The instrument electronics measure the time it takes from transmitted sound to return of the echo. With reference to the speed of sound in air, the exact distance of the liquid surface from the sensor can be calculated with high accuracy (±0.25% of maximum range).
Since the speed of sound is affected by air temperature, ultrasonic level sensors include a built-in temperature sensor. Level/distance measurements are automatically temperature compensated throughout the operating temperature range of the sensor.
The sensor should be positioned so that it has a clear "view" of the liquid surface and away from ladders, pipes or other obstructions. It is recommended 1 ft. from the sidewall for every 10 ft. depth (300 mm for every 3 m depth). False echoes from agitators (sweeping under the sensor), turbulence and waves can be filtered and disregarded by the instrument.